4/11/2023 0 Comments Virtufit iconsole htr 2.1![]() From googling for 5min I found Cardiostrong, Maxxus, Hammer, AsViva, Sportstech, FlowFitness, Luxqueen and so on. Not only for excercise bikes but also for Cross-Trainers. These iConsole computer are beeing built in China and sold as OEM with a lot of brands. I would also volunteer for betatesting if you cannot get hands on such a device. So in my humble opinion it should not be a big deal to support this protocol. On GitHub I found an sample implementation of the iConsole protocol: please see I think if Kinomap can do it, Zwift can do it as well. The app is also controlling the brake, so it should work with Zwift, if Zwift would support the iConsole protocol over Bluetooth. With the MyHomeFit App for Android I receive RPM, Heartrate, Speed, Distance and Watt from the bike and can upload the training units to Garmin. So we bought an Cardiostrong BX70i that is featuring an iConsole computer with Bluetooth connection (and it does much less noise than the wheel-trainer). I used to Zwift on a Tacx Smart Trainer, but my wife also wants to train indoor, but she prefers an excersise bike over the racebike on a trainer, and we don’t have room for two. 17 18.I really would love to see iConsole support in Zwift. 18) onto the seat post by sliding the post into the seat slider while pulling on the pull pin under the seat slider. Locate the seat slider and mount the assembly (Fig. Hardware QTY M8x1.25x12mm hex Screw 2 Final Torque 33-37 Lb-Ft (45-50 Nm) Fig. 17) thru the back of each crank arm and torque each screw to its final value. De hometrainer beschikt over een DVD die je zal helpen om meer uit je training te halen en om meer intensief te trainen voor betere resultaten. Dit is een hometrainer met video app die je zal helpen om beter te trainen. Insert the pedal securing bolts into each pedal (Fig. Als eerst hebben we de VirtuFit iConsole HTR 2.1 Ergometer. ![]() 21) and install the corresponding hardware to lock the plastic sleeve in place.Īssembly Manual 16. Mate the edge of the plastic sleeve flush with the edge of the upright tube (Fig. 20) into the frame by pulling on the pull pin located on the upright column of the frame and sliding the post downward along with the plastic sleeve verifying to lock the post into one of the available positions. Remove all parts from the shipping carton and foam insertĪssembly Manual Hardware QTY M4 x 10mm Phillips Pan Head Thread Form S crew 2 19. Carefully tilt the box forward so that the box may be lifted to expose the bike. Open the top of the carton and fold back all four flaps. UNPACKING AND PARTS LIST Position the shipping carton so the “Heavy End” logo is located at the bottom. 12) toĪssembly Manual StairMaster AirFit Assembly & Setup Use the following procedures to unpack and assemble your AirFit manufactured by StairMaster. Secure the left & right grip arms to the crank linkages by applying final toque (Fig. Hardware QTY M24 x 1.5 Hex Jam Nut 2 Final Torque 48-50 Lb-Ft (65-67.8 Nm) Fig. 11) by threading the large jam nut onto each pivot shaft and applying the corresponding final torque to each nut. Stairmaster AirFit Assembly Manual Hardware QTY M8 x 20mm Button Head Bolt 4 10. 15) stamped into the strap that indicates the user side for i ASSEMBLY TIP Each pedal has an “L” or “R” marking (Fig. 14) over the mounting plates and secure the covers from the underside by bolting four button head cap screws along with washers into the corresponding four available holes. Attach the left & right plastic foot stand covers (Fig. 10) onto the corresponding pivot shafts located onĪssembly Manual Hardware QTY M8 x 15mm Button Head Bolt M 8 x 16mm O.D. 9) to the frame using the four pre- installed Phillips head screws thru each of the available holes on the neck plate. 8) over the neck mast and connect the cable coming out of the mast into the cable protruding from the console. Test the seats horizontal adjĪssembly Manual Hardware QTY M8 x 20mm Socket Head Cap Screw M 8 x 25mm O.D. Check the seat to make sure it is level and tight and does not rotate around or tilt. ![]() Test the seat post to make sure they move freely and you are able to lock in at different positions. Recheck all the bolts and make sure they are all tightened to the proper torque specification (when indicated) and no parts are missing. 3Īssembly Manual Testing Bike Use this checklist to perform the bike test procedure. 2) of the c ardboard box to expose the base and assembly components of the m achine. Cut all straps and remove the top half (Fig. Locate an open area to unbox the packaged machine (Fig.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |